What are the minimum requirements for a safety harness?

OSHA Fall Protection Requirements – Falls on construction sites cause 100,000 injuries and 150 to 200 deaths annually. To mitigate this stark statistic, employers must strategically lay out workplaces to prevent employees from falling off elevated workstations or stepping into holes in the floor.

Any time an employee is six feet or more above the ground and not covered by a safety net or guardrail When erecting or dismantling scaffolding that has an incomplete handrail system or is higher than ten feet above the ground When using aerial equipment that elevates the employee higher than six feet above the ground Any time an employee is less than six feet away from the edge of a floor or roof opening

For scaffolding and steelworkers, the rules differ ; employees on scaffolds ten feet or above must have fall protection and steelworkers must have 15 feet or above. There is also no minimum height when the employee is working alongside risky equipment, machinery, or any hazard into which they could fall.

What safety device should be worn when working on heights above 1.5 m?

There are a wide variety of different safety harnesses available on the market, and they can be used in a number of different ways depending on what kind of attachments you’re using and what environment you’re working in. On the whole, the primary function of a safety harness is to prevent the wearer from falling from a dangerous height.

By wearing the harness, comprised of a system of straps and restraints, the risk of injury caused by a potential fall is greatly reduced. If you work in a job that requires regularly working at great heights, the potential dangers and accidents that could occur at height are one of the biggest causes of injury and fatality in the workplace.

Wearing a harness is the best way to keep yourself safe, but how do you know when you should be wearing one? When Should You Wear a Safety Harness? When Working at Height Fall arrest and restraint lanyards are the perfect equipment to use with harnesses when working at height.

They work by either catching you when you fall (arrest) or preventing the risk of falling altogether by preventing you from moving into areas of risk (restraint). These are only two ways that harnesses can protect you when you’re working at height. If you’d like to get a better idea of the different ways a harness could be utilised to ensure personnel safety, why not browse our wide selection of harnesses, lanyards, anchor points, and more! Browse Safety Harnesses When There’s a Risk of Falling When you’re not working at height, the risk of falling from a smaller drop seems almost insignificant.

Surely it would be a waste of time to spend all that effort setting up the harness and anchoring systems, all for a potential fall that wouldn’t even be that dangerous right? Not necessarily. Even the smallest fall could be potentially life-threatening.

• Falling from a seemingly low height and landing awkwardly could result in broken bones, nerve damage, pulled muscles, or worse.
• Always wear a harness if there’s a risk of fall, no matter how low it is.
• When Is It Legally Required to Wear One? There are a lot of laws and regulations around safety in the workplace, especially when it comes to working at height.

There are a lot of factors that have to be taken into consideration when determining potential fall hazards at a worksite. No two work sites will ever be the same, but it is generally accepted that protection must be provided if there is an unprotected edge with a potential fall of 6ft or higher.

1. The rules vary slightly for different scenarios such as scaffold workers or steelworkers.
2. If you’re looking for more specific information and how the laws pertain to you or your situation specifically, check out the PDF guide on working at height from the Health and Safety Executive (HSE).
3. HSE Working at Height Guide Always ensure you’re properly educated on both the legal requirements for you to be working safely and what precautions you can take to keep yourself safe every day.

All of the above information perfectly encapsulates the many potential dangers of working at height, and why it’s so important to wear a harness. Remember to always check your harness and other equipment carefully before starting work, and check it EVERY time.

1. Inspect carefully for signs of wear and tear, fraying, or damaged buckles.
2. It’s also important to make sure that your anchoring point is equally stable and secure, and that the lanyards are all attached and adjusted appropriately.
3. With the risks associated with falling from height, you can never be too careful.

Always exercise caution. If you have any questions about harness safety or what products would be right for keeping YOU safe, reach out and contact us and we’ll do everything we can to help. Contact Us

What is the maximum safe working height of a low level platform?

The Low Level Work Platform low level work platform is one of the many working at height solution, ideal for those needing low level access platform when working at 3 m and below. Its compact dimensions allow easy transportation,and it fits in the car boot. Lightweight, simple to assemble and dismantle, the Low Level Work Platform has full inbuilt guardrails protection.

One single item no loose parts to lose. One person operation. No Ticket or Training required. 5 Platform Heights 450, 530, 600, 730 and 870mm. Positive locking entry gates. Weight 27kg. Folds for Transport and Storage. Can be transported in an estate car. Safe Working Load of 200kg. Folded Size 1120mm x 760mm x 310mm. Platform Size 760mm x 1120mm. Instructions and equipment in accordance with BS EN 1298.

How is safe working height measured?

A Few Examples Of Working Heights – Just before we finish off, we’ll look at a few practical examples. Our details both the exact platform height as well as the average working height for each variant, helping you to make an informed decision on which tower is best for your needs. Meanwhile, with like our Zarges Z600 Anodised Trade Platform Step, you can see that the tallest model has a platform height of 2.20m.

• Going by the general rule that safe working height is ¾ of your height, a safe working height would therefore be approximately 3.85m.
• At Browns Ladders, we’ve got a huge range of products designed for both home and professional use – you can, or give us a call on 01254 615517 if you have any further questions or queries.

Our experts are here to help! Don’t forget to follow us on Twitter: : What’s The Difference Between Platform Height And Working Height? | Browns

What PPE is required for height work?

Working at Height and PPE – Working at height remains one of the main causes of fatalities and severe injuries in the construction sector as well as other industries. Falls from height consistently feature in the top three work-related accidents in the UK, with an average of 11 fatalities each year as a direct result.

1. The Health and Safety Executive (HSE) estimates that working at height accounts for approximately 30% of all workplace deaths, with the construction sector particularly susceptible to the risks associated with working at height.
2. To minimise risks and hazards associated with working at height, we need to ensure that staff has the correct Personal Protective Equipment (PPE) when working at height.

This is one of the most dangerous types of work and choosing the right PPE is essential to prevent falls and keep workers safe in the workplace. Our blog outlines five essential items of PPE designed for working at height: 1 – Safety Harness A safety harness is an item of personal protective equipment used to prevent falls from height. It is designed to arrest a worker’s fall in the event they lose their grip on what they were holding or while working at height. Safety harnesses work by connecting to an anchor point and distributing the force of impact over the entire body, reducing the likelihood of injury when falling backwards.

Full body harnesses which cover both feet and legs And hip-harnesses which only cover your waist area from above but leave your lower limbs exposed (this type should not be worn alone).

2 – Lanyards and Connecting Devices Understanding what a lanyard is and how they work is the first step to choosing the correct personal protective equipment for your job. Lanyards are worn around the user’s waist and attached to their harness which provides them with additional protection from falling.

The lanyard is then clipped into either the DBI-SALA Davit Hook or DBI-SALA Steellock Connecting Device, which allows for movement through space without the need for additional support, such as depending on a co-worker for safety assistance. Many different types of lanyards are available on the market today.

It is vital to choose a lanyard best suited for your needs before purchasing any equipment. They come in a wide variety of lengths, weights and sizes too with features including high quality webbing, hooks, carabiners and shock absorbers. 3 – Anchor Points and Access Equipment The third element of PPE is anchor points, which should be installed by a competent person. Anchor points must be checked regularly and used according to the manufacturer’s instructions. In addition to installing anchor points, access equipment should also be provided for use on the scaffolding or platform. 4 – Work Restraint A work restraint system is a safety device that prevents workers from falling if they lose their grip or balance. These systems are designed to stop a worker falling more than 2 metres, or 4 metres if the worker is wearing a harness. 5 – Height Safety Helmet A helmet is a protective head covering which may be worn to protect the head from injury. Helmets are designed to absorb shock and protect the skull from serious injury. They are useful for preventing or reducing damage from direct blows, debris from falling at height, and eye injuries or projectiles (e.g., hammering tools).

It is first necessary to identify the task to be carried out by the worker as well as the constraints and risks of the activity that need to be provided for when selecting a safety helmet. Ensure that helmets used across the UK are manufactured to the applicable British Standard. Brimless helmets provide a wider field of vision when working at height. Be aware of vented helmets. Vents cannot be used for those working at heights. undertaking electrical work as cables may come into contact with the wearer through the vent. Chinstraps are required when wearing a helmet for working at heights. Ear and eye protection are required in many industries. Accessories for climbing helmets include attachable ear muffs, full-face visors, and eye shields. Ensure that the helmet conforms to the safety regulations

Why use PPE? If you are working at height, it is vital that you protect yourself with the right PPE equipment. Not only will this help to minimise risks to both yourself and others around you, but it can also help to ensure compliance with health and safety laws. Tetra Ladder Safety System For more information visit or get in touch with us on 028 3839 8700 NI or 01 891 6105 ROI or visit our website for more information Working At Heights | ITS Health & Safety Training Northern Ireland (industrytrainingservices.com) Further reading https://www.hse.gov.uk/work-at-height/ https://www.hsa.ie/eng/publications_and_forms/publications/general_application_regulations/work_at_height.html https://app.croneri.co.uk/feature-articles/what-wear-when-you-re-working-height

What is the maximum height for a ladder?

What’s the maximum working height for ladders? – There is no legal maximum working height for a ladder. But remember, ladders are best for access, and low-risk short duration work at height. Working at height is dangerous, and falls from height are often the top cause of fatal accidents at work (according to ).

• Work at a very high level is unlikely to be low risk.
• You should also provide landing areas or rest platforms at suitable intervals, where a ladder rises 9m or more.
• There is no maximum height for using a ladder.
• However, where a ladder rises 9 metres or more above its base, landing areas or rest platforms should be provided at suitable intervals.

HSE Find out more about safe ladder use in, and download the for your team. : The Law On Ladders And Maximum Working Heights

At what height is a harness required on a scissor lift?

OSHA Scissor Lift Safety Requirements – When it comes to scissor lifts, OSHA’s top concern is that only workers who have undergone the necessary training and certification be permitted to operate different types of Advanced Work Packagings (AWP). According to an OSHA-conducted study, the majority of scissor lift accidents occur in workplaces where employers have neglected the proper prevention and safety training.

Employers are required by OSHA’s regulations to instruct operators on the proper safety procedures. Any employee who uses a scissor lift must get the appropriate training. OSHA mandates that operators renew their and certification every three years. It is the employer’s duty to ensure that every operator receives OSHA-approved instruction and certification.

This is done to make sure operators learn the safety guidelines for scissor lifts, such as how to inspect and maintain the machinery and adhere to the manufacturer’s instructions. The appropriate use of personal protective equipment (PPE) must also be covered in the training.

1. Scissor lifts must always be provided with guardrails that are in place at all times in accordance with OSHA rules.
2. This is mandated for anywhere that scissor lifts are used, including interior and outdoor construction, sign maintenance, and shipyard operations.
3. Workers should always wear fall protection harnesses that are firmly connected to the lift if the platform is more than 10 feet above the ground or a platform directly below if guardrails aren’t accessible.

Workers should never stand on, lean against, or use the guardrails of a scissor lift for stability purposes.

Is there an age limit on safety harnesses?

The Official Advice On When To Replace Safety Harnesses – As a general rule, the average lifespan of a typical safety harness is around five years. This does depend on the make and model of the harness itself – some are even approved for up to ten years. Again, this depends on the capabilities of the individual pieces of equipment, and the recommendations of the manufacturer. But, don’t stop reading there! While the law doesn’t give any concrete, arbitrary time limits on when to change equipment, the Work at Height Regulations 2005 requires that for any equipment exposed to conditions that might cause deterioration (a category that very much includes safety harnesses and lanyards), employers need to inspect them at regular intervals, as well as immediately after any events that might have put it under particular physical stress.

Why do you need a safety belt?

Seat belts are primarily employed to protect passengers from injuries in the case of an accident. As per Newton’s first law of motion, when a car abruptly stops or crashes, Due to inertia of motion, a person sitting in a moving car may be pushed forward when the car stops abruptly, potentially causing damage.

Who has to be wearing a safety belt in the car?

State-By-State Seat Belt Laws – Alabama – In 1999, the “Yellowhammer State” changed from a secondary to a primary seat belt law. The state requires front seat occupants to wear safety belts properly at all times when the vehicle is in motion. All children under the age of 5 must have the proper child passenger restraint system for their age and size.

1. Children from 6 to 15 must always wear a seatbelt.
2. Prior to 2006, the seat belt laws only covered passengers through the age of 3 years.
3. Alaska – In 2006, “The Last Frontier” state became the 23 rd state to enact a primary seat belt law.
4. All occupants of a vehicle are required to wear the appropriate restraints.

Arizona – All front-seat passengers are required to wear a properly fitted restraint while riding in “The Grand Canyon State.” Those under the age of 16 years must buckle up in the front or rear seats. Arizona’s seat belt laws only apply to vehicles manufactured in 1972 or newer while carrying no more than ten passengers.

• Arizona has a secondary seat belt law.
• Arkansas – “The Natural State” has a primary seat belt law that requires children riding in the front or rear seats to buckle up.
• Ids must ride in an appropriate child restraint system until they reach the age of 6 years or 60 pounds.
• California – California takes their seat belt laws seriously.

“The Golden State” cites extensive evidence that seat belts save lives for their strong seat belt laws. Every adult over the age of 16 years must wear an approved seat belt. Occupants younger than 16 are required to use an appropriate car seat or booster seat.

The law extends to the use of lower seat belts which cross the hips or upper thighs and the upper seat belt which they require occupants to wear across the front chest. In addition to holding passengers accountable for buckling up, the driver is also responsible for the actions of every passenger. The primary seat belt law allows officers to stop you and ticket you for failing to wear a seat belt or wearing it improperly.

Colorado – The driver and all passengers must wear a seat belt in “The Centennial State.” The secondary seat belt law only allows officers to ticket you after stopping you for a separate offense. On the other hand, Colorado’s seat belt laws allow officers to pull drivers over when a child passenger isn’t properly restrained.

1. If you are ticketed for failing to properly restrain a child, not wearing a seat belt could become a secondary offense after the officer pulls you over.
2. Connecticut – “The Constitution State” considers seat belt violations as a secondary offense.
3. All front seat passengers must wear a seat belt in addition to rear-seat passengers between the ages of 4 and 16 years.

If you are cited for a secondary offense, you are responsible for any of your passengers that aren’t buckled up too! Delaware – “The First State” has primary seat belt laws for drivers and passengers aged 16 years and older. The state boasts 92% seat belt use compared to the national use rate of 86%.

Their no-nonsense approach to buckling up through their “Click It or Ticket” enforcement is setting an example for other states with less strict laws. Florida – If you plan to drive in “The Sunshine State” in a car manufactured since 1968, everyone in the front seat must wear a seat belt. Those under the age of 18 years must use the appropriate seat belt or child restraint.

Florida is a secondary seat belt state that doesn’t allow law enforcement to stop you for failing to wear a seat belt. Georgia – “The Peach State” has a primary seat belt state law requiring drivers and passengers in the front seat aged 18 years and older to wear a seat belt.

• Passengers between the ages of 8 and 17 must wear a seat belt in any seat of the vehicle.
• Child restraint laws apply to any passenger under the age of 8 years old.
• Hawaii – “The Aloha State” isn’t as welcoming to visitors who ignore their seat belt laws.
• Hawaii has primary seat belt laws that require the driver and all passengers to wear a seat belt.

Drivers pay between $102 and $112 for violating the seat belt laws or take a four-hour safety class and pay $100 to $500 if they violate the child restraint laws. Idaho – “The Gem State” has a secondary seat belt law which requires everyone in any vehicle to buckle up.

Idaho holds drivers accountable for passengers under the age of 18 who are not appropriately restrained. Illinois – Anyone aged 8 years and older must buckle up in “The Prairie State.” The laws extend to vehicles with airbags. Any passenger under the age of 8 years must be secured in an acceptable child restraint system.

Illinois has a primary seat belt law that allows officers to stop and ticket you for seat belt offenses. Indiana – The law requires anyone in the car to wear a seatbelt while going in forward motion in “The Hoosier State.” This primary seat belt state implements stricter laws on offenses involving the failure to use proper child restraints.

• Iowa – Passengers under the age of 6 years must be secured in a proper safety seat or booster seat while riding in “The Hawkeye State.” Children aged from 6 to 11 years must either wear a safety belt or child restraint system.
• Those under the age of 18 years must wear a seat belt.
• Iowa is a primary seat belt state.

Kansas – Kansas is a primary seatbelt state with regards to stopping and ticketing drivers and front seat passengers under the age of 18 who aren’t wearing a seat belt. A secondary seat belt law applies to passengers in the back seat allowing law enforcement in “The Sunflower State” to write a ticket after you are already stopped.

Entucky – “The Bluegrass State” has been resistant to updating seat belt laws, in spite of the best efforts of former Governor Steve Beshear. Today, all passengers who aren’t covered by laws mandating child restraints must wear seat belts. Kentucky allows those with a physician’s letter citing medical conditions to forego the restraints.

The state has a primary seat belt law and requires everyone wearing a seat belt to have it properly adjusted and fastened. Louisiana – Louisiana requires drivers of vehicles with a gross weight of ten thousand pounds or less to wear a seat belt while in forward motion.

• The Pelican State” applies their primary laws to vehicles manufactured on or after January 1, 1981.
• Some types of service vehicles are also excluded from the law.
• Maine – As of September 2007, “The Pine Tree State” is a primary seat belt state.
• Maine requires drivers and passengers aged 18 and older to wear a seatbelt.

Additional laws mandate the use of appropriate child-restraint systems for children in any vehicle. Maryland – “The Old Line State” has a split law, applying primary laws to passengers under the age of 16. Those over the age of 16 in the front or rear seat are required to wear a seatbelt but not wearing one is treated as a secondary offense.

1. Massachusetts – When driving in “The Bay State”, all occupants of the car aged 13 years and older must wear seat belts.
2. Those with a disability or medical condition that makes belt use difficult or impossible require proof from a physician to forego the law.
3. Vehicles manufactured prior to July of 1966 and some types of emergency vehicles are exempt.

Michigan – Drivers in “The Great Lakes State” must abide by primary seat belt law. Michigan requires passengers between the ages of 8 and 15 years to buckle up regardless of where they ride. All drivers and front-seat passengers must wear a seatbelt. Minnesota – “The North Star State” has primary seat belt laws mandating all passengers and drivers to buckle up.

Children must also wear appropriate child restraints and all restraining devices must be worn correctly. Minnesota offers stiff penalties to the driver for a first offense, often exceeding $100. Mississippi – “The Magnolia State” passed a new seat belt law in 2017, requiring everyone in all types of vehicles to wear seat belts.

Mississippi also has primary seat belts laws for passengers aged 7 years and older, taller than 57 inches, or who weigh more than 65 pounds. The new law prohibits anyone from riding in the bed of a pickup truck. Missouri – “The Show Me State” currently has secondary seat belt laws, but a bipartisan group of Missouri mayors has made getting a primary seat belt law a priority.

The group, known as the “Missouri Mayors United for Progress,” wants to implement a bill that subjects failing to buckle up to fines, along with texting while driving, Currently, Missouri requires all drivers and front-seat passengers to wear seat belts. When the driver has an intermediate driver’s license, all occupants in the vehicle must buckle up.

Montana – Montana has a secondary seat belt law that applies to drivers and all other occupants in a vehicle. “The Treasure State” requires appropriate child restraints for children under 6 years of age or who weigh less than 60 pounds. Nebraska – “The Cornhusker State” has a secondary seat belt law and requires drivers and front-seat passengers to buckle up.

In vehicles with drivers having a provisional operator’s permit or school permit, all passengers must buckle up. Nevada – Nevada is another state with secondary seat belt laws. “The Silver State” requires all occupants to wear seat belts or wear the proper restraining device according to their age. Vehicles manufactured in 1968 or newer must be equipped with lap belts.

Those manufactured in 1970 or later must have both lap belts and shoulder belts in the front seats. New Hampshire – As mentioned earlier, New Hampshire is the only state that doesn’t have a primary or secondary seat belt law which applies to adults. However, “The Granite State” does have a primary child passenger safety law mandating the use of seat belts or safety restraints for drivers and passengers under the age of 18 years.

• New Jersey – In New Jersey, passengers in the front seat who don’t wear a seatbelt are subject to charges of a primary offense.
• The Garden State” might charge those in the backseat with a secondary offense.
• New Mexico – In “The Land of Enchantment”, anyone riding in a vehicle that was manufactured with seatbelts is required to buckle up while the vehicle is in motion.

New Mexico has a primary seat belt law, which allows law enforcement to stop and ticket drivers for seat belt offenses. New York – “The Empire State” has a primary seat belt law that requires all front seat passengers to buckle up. Children under the age of 16 who ride in the rear seat must buckle up.

1. Children under the age of 4 years must use appropriate child safety seats.
2. North Carolina – The primary seat belt law in North Dakota mandates that all occupants aged 16 years and older must wear a seat belt.
3. The seat belt laws in “The Tar Heel State” extend to all vehicles required by federal law to be equipped with seatbelts.

North Dakota – “The Peace Garden State” has a secondary seat belt law which requires all drivers and passengers in the front seat to wear a seat belt that is properly fastened. Any occupant under the age of 18 years must be properly restrained in either the front or rear seat.

1. Ohio – Ohio is another state with a secondary seat belt law.
2. The Buckeye State” requires drivers and front seat passengers aged 15 years and older to wear a seat belt.
3. Passengers between the ages of 8 and 14 years must wear a seat belt in the front or rear seats.
4. Children under the age of 8 years must use a proper child restraint system.

Oklahoma – “The Sooner State” has a primary seat belt law requiring everyone in the front seat to wear a seat belt. Oklahoma holds drivers liable for securing any passenger under the age of 12 years. Oregon – “The Beaver State” has a primary seat belt law requiring drivers to always buckle up.

Oregon requires children under the age of 16 years to use a child safety system, safety harness, or belt. Pennsylvania – Pennsylvania is another primary seat belt state that requires all occupants in the front seat to buckle up. “The Keystone State” requires passengers between the ages of 8 and 18 years to wear a seat belt in the front or rear seats.

Fines vary according to the age of the person failing to wear a seatbelt. Rhode Island – In “The Ocean State”, drivers are required to wear a safety belt and/or shoulder harness system at any time the vehicle is in motion. The primary state requires passengers 8 years or older to wear an appropriate child restraint system while riding in either seat.

South Carolina – South Carolina has a primary seat belt law, which requires every occupant of the vehicle to wear a seat belt. “The Palmetto State” also holds drivers responsible for ensuring any passenger without a license and who is 17 years old or younger wears a seat belt. South Dakota – The “Mount Rushmore State” had one of the lowest seat belt usage rates in the country before 1994.

The state has a secondary seat belt law that has increased seat belt compliance from 26% to 88%. South Dakota requires all occupants in the front seat to wear properly fitted restraints while the vehicle is moving forward. Drivers are held accountable for passengers between the ages of 5 and 18 years being buckled up.

Tennessee – “The Volunteer State’ has a primary seat belt law that requires drivers to wear seat belts any time the vehicle is in motion. Passengers in the front seat must wear properly fastened seatbelts. Children under 18 years must wear safety restraints in any seat. Texas – Texas has a primary seat belt law that allows law enforcement to stop and ticket drivers for seat belt offenses.

“The Lone Star State” assesses fines between $25 and $250 for seal belt offenses in addition to court costs. Utah – “The Beehive State” has a primary seat belt law as of 2015. Utah requires all occupants to wear seat belts. In addition, children aged 8 and younger must be restrained with the appropriate car seat or booster seat.

• Vermont – Vermont is another of the states to observe split primary and secondary seat belt laws.
• The Green Mountain State” observes primary laws for all occupants of a vehicle aged 18 years old and under.
• Secondary laws apply to drivers and passengers over the age of 18.
• Virginia – “The Old Dominion State” has a secondary seatbelt law.

Virginia requires all front and rear seat occupants to buckle up and anyone under the age of 18 must use a proper child restraint. The state holds drivers responsible for buckling all passengers. Washington – The State of Washington has a primary seat belt law requiring anyone over 8 years of age or over 4’9″ to buckle up.

“The Evergreen State” adopted stricter seat belt laws in 2007 adding that children younger than 8 years or smaller than 4’9″ must wear a safety restraint system or use a booster seat. They also require children under the age of 13 years to ride in the back seat when proper restraints aren’t an option in the front seat.

West Virginia – “The Mountain State” has a primary seatbelt law requiring all occupants in the front seat to buckle up. Any rear-seat passenger under 18 years old must also wear a seat belt. Wisconsin – Drivers in “The Badger State” must buckle up at all times using three-point seat belts,

Wisconsin has a primary seatbelt law that requires passengers under the age of 4 years to use appropriate child safety restraints. Drivers can be ticketed for seat belt offenses by them or their passengers. Wyoming – Whether you refer to Wyoming as “The Equality” or “Cowboy State”, drivers must follow the secondary seat belt law.

The law mandating seat belt use applies to all occupants in the front and rear seats. Children under the age of 9 years must be in a proper child restraint system that is properly fastened. Wyoming holds drivers liable for all passengers buckling up. All 50 states take the issue of restraining children seriously. To find out all of the seat belt laws in your state, visit your local DMV website. Never assume that seatbelts aren’t required when riding in something other than a standard passenger vehicle.

• For example, the growing popularity of rideshare companies like Uber and Lyft have changed the way we look at liability.
• Some states have already adopted stricter laws regarding seat belt use while others are working to increase seat belt requirements.
• Make sure you investigate your state’s laws regularly to stay up-to-date.

The best approach is to always buckle up securely whether you are a driver or passenger. Remember, the primary goal of buckling up is to save lives. If you’ve been injured in an accident caused by another person, contact Batta Fulkerson for a free consultation.

Jack Gloop