What are the measures for electrical safety?
Safety Precautions for Electrical Hazards – Employers should diligently apply the Occupational Safety and Health Administration’s (OSHA) recommendations for electrical safety standards, These include:
Always wear adequate safety gloves when touching electrical wires (even insulated ones) Inspect your surroundings before working on power lines or power stationsDeal with any wetness or dampness on your person or surroundings before working with electricityElectrical wires or devices should only be repaired by qualified and authorized personnel Ensure that all electrical devices are grounded before dealing with themMake sure electrical circuit breakers are in place before performing maintenance on electrical devices
What are the three elements of a basic program for electrical safety?
The three elements of a basic program for electrical safety are: Recognize, evaluate, and control. All portable electric tools that are damaged shall be: Removed from us and tagged ‘Do Not Use.’
Which safety guideline should be followed when working on electrical equipment?
It’s vitally important to take safety precautions when working with electricity, Safety must not be compromised and some ground rules need to be followed first. The basic guidelines regarding electrical safety documented below will help you while working with electricity.
- 1. The first step of electrical safety, avoid water at all times when working with electricity.
- Never touch or try repairing any electrical equipment or circuits with wet hands.
- It increases the conductivity of the electric current.2.
- Never use equipment with frayed cords, damaged insulation, or broken plugs.3.
If you are working on any receptacle at your home then always turn off the mains. It is also a good idea to put up a sign on the service panel so that nobody turns the main switch ON by accident.4. Always use insulated tools while working. 5. Electrical hazards include exposed energized parts and unguarded electrical equipment which may become energized unexpectedly. Such equipment always carries warning signs like “Shock Risk”. Always be observant of such signs and follow the safety rules established by the electrical code followed by the country you’re in.6.
- Always use appropriate insulated rubber gloves and goggles while working on any branch circuit or any other electrical circuit.7.
- Never try repairing energized equipment.
- Always check that it is de-energized first by using a tester.
- When an electric tester touches a live or hot wire, the bulb inside the tester lights up showing that an electrical current is flowing through the respective wire.
Check all the wires, the outer metallic covering of the service panel, and any other hanging wires with an electrical tester before proceeding with your work.8. Never use an aluminum or steel ladder if you are working on any receptacle at height in your home.
An electrical surge will ground you and the whole electric current will pass through your body. Use a bamboo, wooden or a fiberglass ladder instead.9. Know the wire code of your country.10. Always check all your GFCI’s once a month. A GFCI (Ground Fault Circuit Interrupter) is a RCD (Residual Current Device).
They have become very common in modern homes, especially damp areas like the bathroom and kitchen, as they help avoid electrical shock hazards. It is designed to disconnect quickly enough to avoid any injury caused by over-current or short circuit faults. Previously Published on SafetyRisk.net For more safety materials on Electrical Safety, visit our PowerPoints and Infographics dedicated to this focus.
What are the objectives of electrical safety?
Electrical Safety The danger of injury and/or property damage through electrical shock is possible whenever electrical power is present. When a person’s body completes a circuit and thus connects a power source with the ground, an electrical burn or injury is imminent.
- Most fatal injuries result from high-voltage exposure; however, people can sustain severe injuries from low voltage power if it has a high current flow.
- OSEH strives to protect all employees, students, and other personnel from potential electrical hazards.
- This will be accomplished through compliance with the work practices described in this Program.
The objective of the Electrical Safety Program is to minimize such potential hazards by specifying proper use and design characteristics of electrical devices, equipment and systems. The University’s Electrical Safety Program is based on that were carefully developed to cover only those parts of any electrical system that a user would normally use or contact.
The exposed and/or operating elements of an electrical installation – lighting equipment, motors, machines, appliances, switches, controls, enclosures, etc. – must be so constructed, installed and maintained as to minimize electrical dangers to people in any workplace or occupancy. Please contact EHS at (313)593-0921 for more information.
: Electrical Safety